How to Get My Image Drum Working Again
Resolving the "Replace Brother Drum" message
This " replace drum " message is a problem that nosotros go asked about frequently. So if this has happened to y'all, please be assured that you're not lone! Fixing or replacing your Blood brother pulsate is a simple procedure that anyone can do.
Hither's exactly what y'all can acquire from this page to assistance y'all to replace or resolve your Blood brother drum message:
- What does the 'Replace Drum' message hateful?
- How to find, remove and replace the Brother drum
- How to reset the drum and articulate the 'Supersede Drum' message.
- Where to buy a new Brother Drum Unit.
What does supercede drum mean?
A drum unit is a maintenance item for your Brother printer (or other manufacturer Light amplification by stimulated emission of radiation printer) that will sometimes need to be replaced but not as often as a toner cartridge.
A pulsate unit is a green metallic cylinder or tube that carries a static electric charge that attracts the toner powder from the toner cartridge and applies it to the paper as information technology passes through the printer. Therefore, you will ever notice that drum unit is located very shut to or even attached to the toner cartridge.
How to find, remove and supersede the Brother drum unit
For Brother printers, the drum unit is unremarkably connected to the toner cartridge.
1. To discover it, merely open up the front flap of your laser printer and find the toner cartridge(s) which the pulsate unit will be attached to or beneath.
two. Pull any greenish toner locking levers down to release the cartridge and then slowly pull the cartridge towards yourself and out of the machine. Identify the toners on a flat protected surface.
three. On the toner cartridge(s) there will exist a green lever that can exist pressed to lift the toner off the drum unit.
iv. The pulsate unit can then be replaced and toner locked back into identify on top of the new drum.
five. Re-insert both toner and pulsate back into your printer.
Clearing the 'Replace Drum' message / resetting the counter
If y'all've only replaced the pulsate unit of your Brother printer, are yous now seeing the bulletin "Supercede Drum"?
The cause
Ink and toner cartridges, equally well as the drum units of another manufacturers, have chips on them. Basically these fries are a way for the cartridges and pulsate units to identify themselves with the printer after you lot've installed them.
However, some original and compatible Brother drum units don't take these, and this is the case with the drum unit. Without a chip, your drum unit has no way of being able to associate itself with your Blood brother printer. As a outcome, you lot volition get the "Replace Drum" message considering your printer thinks that you've not installed a pulsate unit.
On the right is a standard toner cartridge with a bit. The DR2200 drum unit (left) doesn't take one of these.
The solution
Don't panic. There'southward no need to ring up your supplier for a replacement. There'due south ane really elementary task that yous can do to reset your printer and get it up and running again.
If you've got a Blood brother MFC-7360N, MFC-7460N, MFC-7460DN or MFC-7860DW
On your printer:
-
Press 'Clear'
-
Press the number ane
-
Ensure that you at present meet the "Accepted" message on your brandish
If you've got a Blood brother DCP-7055, DCP-7055W, DCP-7060D, DCP-7065DN or DCP-7070DW
On your printer:
-
Printing 'Articulate'
-
Press the upward arrow
-
Ensure that you now run into the "Accustomed" message on your display
And that should sort it out!
This guidance works for almost all of our customers that band usa concerned later they've just bought their new DR2200 unit or any other drum unit. We hope that it's now worked for y'all, too.
Buying a new Brother Pulsate Unit
If you're looking to purchase a make new brother drum unit to supersede your current ane. Nosotros sell a full range of Brother drums and toners at TonerGiant.co.britain. Just visit the Brother toner page, navigate to your printer model using the wizard and the correct Blood brother pulsate will be listed on the resulting page.
Did it work? What other problems accept you lot experienced similar this? We'd love to hear from you! Leave us a comment below or tweet usa @tonergiant.
Updated 10/01/2017 to improve the data and provide additional aid
I have been working in the printing industry with TonerGiant for over 12 years and am the resident technical printer adept. I'yard also the Digital Marketing Manager at TonerGiant.co.uk (degree qualified) and I have a passion for helping people fix their printer issues. I'chiliad besides a big fan of all gadgets and technology.
Source: https://www.tonergiant.co.uk/blog/2014/05/how-to-resolve-replace-drum-message-after-changing-brother-drum-unit/
0 Response to "How to Get My Image Drum Working Again"
Postar um comentário